The Project Gutenberg EBook of Wood Engraving by R. John Beedham
This eBook is for the use of anyone anywhere at no cost and with almost no
restrictions whatsoever. You may copy it, give it away or re-use it under
the terms of the Project Gutenberg License included with this eBook or
online at http://www.gutenberg.org/license
Title: Wood Engraving
Author: R. John Beedham
Release Date: January 6, 2014 [Ebook #44606]
Language: English
Character set encoding: UTF‐8
***START OF THE PROJECT GUTENBERG EBOOK WOOD ENGRAVING***
WOOD ENGRAVING
By R. JOHN BEEDHAM
WITH INTRODUCTION AND APPENDIX
BY ERIC GILL
[]
FABER AND FABER LIMITED
24 RUSSELL SQUARE
LONDON. 1921
CONTENTS
INTRODUCTION TO SECOND EDITION
WOOD-ENGRAVING PAST AND PRESENT
WOOD ENGRAVING
THE WOOD
DRAWING
ENGRAVING
PROOF TAKING
PREPARING BLOCK FOR PRINTER
PLUGGING
APPENDIX
ILLUSTRATIONS
Wood-cut from The Decameron, Venice, 1492. Re-engraved by R. J. Beedham.
By permission of The Shakespeare Head Press
Alphabet, by Reynolds Stone _(By permission of Burns, Gates & Washbourne,
Ltd.)_
_From_ Forrest Reid’s Apostate, by Reynolds Stone _(By permission of Faber
& Faber, Ltd.)_
Winter, from a sketch by Verrall, by R. J. Beedham
Strawberry Picking, by Claire Leighton _(By permission of Victor
Gollancz)_
March, by Mrs. G. Raverat
“Miss Jenkyns reading Rasselas,” by Joan Hassall _(By permission of George
G. Harrap & Co., Ltd.)_
The Cottage, by Robert Gibbings
INTRODUCTION TO SECOND EDITION
This book is not a treatise upon the _art_ of wood-engraving. It is simply
a description of the tools and materials required by a beginner and the
method of using them. It is not intended to assist anyone to become a
commercial engraver, for that trade requires a long and specialized
training. It is intended rather for those who have occasion or opportunity
or inclination to make illustrations or ornaments for books and who are
revolted by the degradation to which the art of formal drawing has been
brought by photographic “process” reproduction.
The “line” block and the “half-tone” have one clear claim to usefulness:
viz. when an exact facsimile is required. It is doubtful, however, whether
process reproduction would have been developed very far if its use had
been confined to those occasions, and those only, when exact facsimile was
of vital importance. Process reproduction owes its success to its
commercial possibilities more than to its real merits, for, in spite of
the frequently reiterated boast of those engaged in business that nothing
can be a commercial success that does not “supply a want,” by photographic
reproduction a speed and cheapness have been obtained which have seduced
both artists and the public. A “want” has certainly been supplied, but it
is a want of quantity rather than of quality, and, as in all cases where
quantitative ideas are the motive force, quality has inevitably
deteriorated so that book production has become a mere business and with
no criterion save that of a commercial success.
It is of course impossible to stem the tide of commercial degradation
until Poverty, Chastity, and Obedience take the place of Riches, Pleasure,
and _Laisser-faire_ as personal and national ideals. Such a change of
heart cannot occur merely as the result of economic or social or
philosophical propaganda; the matter is more fundamental than that. The
modern world is founded upon a denial of absolute values, a denial of
religion, a denial of God; upon such denials nothing can be built.
Goodness becomes what the police will allow or can enforce. Beauty becomes
what pleases the senses and Truth becomes what will pay.
Meanwhile it is possible for any individual that wills to do so to go out
into the wilderness and to live and work in a manner more in harmony with
the nature of man and the will of God. For it is in accord neither with
the will of God nor the nature of man that any one should love himself
more than his neighbour or his neighbour more than God. The present state
of affairs is an unnatural and abnormal thing. It is a disease. And any
one can by the grace of God cure at least himself and put his own affairs
in order.
In the domain of art the remedy is the same as in any other. The thing
good in itself must be found and loved. Relative values must give place to
absolute, the lovely and lovable to the beautiful. “Does it pay?” is not
the question. Is it good in itself?—That is the important thing. And the
more you apply that standard to your own work and to that of others, the
more you will find the necessity of personal responsibility.
But personal responsibility for work done is, from the point of view of
commercial success, actually an evil! Make men responsible for their work
and not merely for doing what they are told; make their own consciences
their masters and the whole of our modern factory system will come
tumbling down like a house of cards. For the factory system is a servile
system in which personal responsibility is denied and of no factory
article may you say: this is the work of such an one—he made it. In the
matter of drawing and illustration and engraving, degradation is
inevitable when one man draws, another touches up the drawing, another
photographs, another touches up the negative, another prints it on the
metal, another etches, another touches up the etching, another routs it,
another mounts it, another proves it and another keeps the accounts and to
crown all, another takes the profits. This excessive sub-division is
inevitable where profit making is the motive power. It is, however, the
artist and the workman who are to be blamed, not the man of business. (The
man of business does his job very well. Certainly he has no right to be
ruler, as he is at present, but it is _our_ fault for allowing him to
rule.) And as good men must precede good law, and not _vice versa,_ so the
individual must revolt against the evil system and not wait until the many
are prepared to revolt with him. Wood-engraving and wood-cutting have gone
out of general use not because photographic process reproduction is
better, or even because it is cheaper and quicker, but simply because
larger profits can be made by employing many persons under a system of
divided labour than by working in a small workshop and putting the quality
of the work before the quantity of the output. The consumer or customer is
flattered and his grosser appetites appealed to. The merchant does not ask
himself what good thing he can supply but what he can supply at a good
profit. The whole trouble is that the responsibility for the making of
things is not in the hands of the workman but in those of the man of
business—and this is hell.
The advantage of wood-engraving then is that it does away with several
sets of middle men and places responsibility upon the shoulders of the
workman. The workman who draws, engraves and prints his own blocks is
master of the situation. He can blame nobody but himself if his work goes
wrong. Whether it goes right or wrong depends upon his notions of right
and wrong. The first thing is that he should be free to satisfy his own
conscience and not be a mere tool in the hands of another. Liber est causa
sui, servus autem ordinatur ad alium (i.e. The freeman is responsible to
himself—but for the slave someone else is responsible. Saint Thomas
Aquinas, _Summa Theologica)._
Another advantage of wood-engraving is that it forces upon the workman
some respect for the thing in itself and makes it impossible for him to
place a merely relative value upon the art of drawing. Mere likeness to
nature is much more easily achieved by drawing, whether in line or wash,
upon paper. The graver and the wood both of them make their own demands
and make mere imitation of nature almost impossible. The workman is
compelled to consider his work primarily as an engraving and only
secondarily as a representation. This is a good thing, for a work of art
is primarily a thing of Beauty in itself and not a representation of
something else, however beautiful that other thing may be. This the public
does not understand. Hence the absurdity of allowing the public to be
supplied by persons who are not workmen and who have no knowledge of the
implications of good workmanship but are simply men of business out to
supply whatever is most profitable to themselves.
He who would be an engraver must therefore start with a clear
understanding that there is “no money in it”; though if he be patient and
devoted he may make a living or a part of a living by it. Further, he must
be prepared to start with the wood and the graver and his sense of what is
beautiful in itself and not strain after effects. He should take it for
granted that a zig-zag pattern such as a child would engrave is better
than the most expert imitation of a sunset. In fact he must be pre pared
to begin at the beginning and to put the first things first.
E. G.
WOOD-ENGRAVING PAST AND PRESENT
Although Mr. Eric Gill in his introduction has explained that this book is
not a treatise on the art of wood-engraving, I feel constrained to add a
chapter to the present edition of the work, chiefly on the past and modern
styles of wood engraving; also to give some information to the younger
craftsmen, some of whom, having lived only in an age of photo-mechanical
reproduction, are quite unaware of the important part that wood engraving
has had in the past for the purposes of book-illustration.
It is a very old craft, older than book-printing from type. It quickly
became the chief means of decorating and illustrating books, and continued
to be so until the invention of photographic processes, which, for general
purposes have supplanted it. Some of the old blocks, cut in simple
outline, fit the printed page in a most admirable manner; in their
particular style they have not been surpassed. An example of this is the
re-cut from _The Decameron_ 1492 on page 47. These early blocks were all
cut on the long grain of the wood, a method that continued until it was
discovered that the end grain was a better medium for cutting of fine
lines for shading or outline.
It is a disputed point whether artists like Dürer or Holbein engraved
their own work. It was probably left to the expert to cut in faithful
facsimile the drawings done by the artist on wood. With a few notable
exceptions, this method of the division of labour, the artist being one
person and the engraver another, continued until wood-engraving was
supplanted by process. For reproductive purposes it was a natural
division. After that a completely new style of engraving, that of the
present day, came into being.
Thomas Bewick was one of the great exceptions to this division of artist
and engraver. Not only did he engrave his own drawings, but he evolved a
completely new style. He abandoned elaborate cross hatching, and for the
most part cut in the most direct and simple way. Nevertheless, for
ordinary reproductive purposes the artist and engraver continued to be
different persons; the artist continued to draw on the wood, filling the
shading with a wash of Indian ink and finishing by means of pen or pencil
lines, or perhaps using the pen alone, but whether drawn by pen or pencil
the engraver faithfully reproduced it, line by line. This necessitated
great skill on the part of the engraver, for the merest thickening or
thinning of the lines altered the effect of the drawing. But sometimes the
drawing was done by wash only, in which case the engraver kept as nearly
as he could to the shade or tone of the original without the aid of
cross-hatching.
This continued until photography made itself felt. It is remarkable that a
vast industry, of which the cinema is the latest development, should have
arisen as the result of the discovery that certain substances changed
their colour and character in the presence of light. It first greatly
influenced wood-engraving and finally ousted it as a means of
reproduction. Photographers found a way of photographing on to the wood
not only drawings but other photographs, and the engraver had to adjust
his style to the new medium, for to cut direct from a photograph was very
different from cutting facsimile from a drawing. The black lines of
cross-hatching disappeared and white lines took their place. Whenever
possible a white line was cut and cross-hatching, where it was necessary,
consisted of white lines crossing each other. Not only so but a method of
cutting short white lines or dots, known generally as stippling, came to
be used. Reproductive engraving speeded up and became a miracle of skill.
The use of stipple reached its outstanding development in the work of the
American, Timothy Cole. In his engravings of the Old Masters he got
amazing effects of atmosphere by means of stippling alone.
The same photographic influence made itself felt amongst the commercial
engravers of machinery. The black outlines of the machine became altered
to white lines whenever possible, and as in the pictorial field, the style
became completely altered. Here let me say that the engraving of machinery
for commercial catalogues is one of the most exacting forms of engraving
that I know. As a means of showing the object perfectly it holds its own
to the present day. There are a rapidly dwindling few who still manage to
get a living from it.
The great skill of the reproductive engraver was amazing. On the staff of
some of the periodicals, where speed joined to excellence of cutting was
essential, there were engravers who could cut a good portrait in two
hours, and this in the style just described, line upon line in the
perfectly free precision of the time. But this skill of the old
reproductive engraver, skill largely for its own sake I fear, made more
easy his undoing. Individuality became partly lost in the skill of
technique. It sometimes seemed as if he were imitating his great
competitor, the process block. The Americans were, I think, great
offenders in this. Though a most lovely craft, wood-engraving, just before
it was superseded by process, had not within it sufficient originality and
power to hold its own. It was largely reproductive only: the real artist
was too often left out. Process developed rapidly as the more effective
way of reproducing originals of one sort or another, and the reproductive
engraver was bereft of his craft. The output of engravings had been
enormous. Some of the old-established printing and publishing firms
cherish their old wood blocks: they belong to the furniture of the past.
Others sold their blocks to the boxwood merchant, not by the block but by
the ton!
The period just preceding the influence of photography was one, in the
writer’s opinion, when reproductive engraving reached its highest level
for book illustration. The engravings of this period, if properly printed,
appeal for the quality of their softness, their skill, and a sweetness of
effect seldom accomplished by the modern style. In many of the volumes of
this period are wood-engravings unequalled in their fidelity to the
objects shown, and that have a beauty not surpassed by modern or any other
engraving. But the days when they were engraved are long since past. We
wait again for their revival, which I believe will come, for it is too
good a thing to be entirely lost. But it cannot come as it came before:
that never happens. The difference will be that the artist will do his own
engraving. There are engravers of the present time, who, almost
unconsciously, are doing work much in the style of this period.
The modern revival of wood-engraving, which came just after the war, is
quite different in style from any that preceded it. The artist and
engraver are now one, as they should be where original work is to be done,
and every exponent of the craft expresses his or her own individuality.
The technique of the old school was swept completely away. “Start
engraving with an axe” was an exhortation overheard, and some of the
earliest examples, with their masses of unrelieved black, rather look as
if they had been engraved by that implement. Design is the outstanding
quality of the present style. Twenty years has brought command of the
engraving tool and now most excellent work is produced with the
originality of the artist-craftsman upon it. The early crudeness having
gone, the modern engraver brings to the printed page a decoration
outstanding in effect. Amongst the mass of process reproduction is the
Wood-engraver, engraving his own designs, thereby expressing an
originality which will most certainly mark the present age of
book-production as something well worth examination. It is therefore
essential that the modern engraver design his own engravings and he will
select the kind of tools which will best express his own individuality,
for it is this individuality of the artist which alone amongst all its
competitors will keep alive Wood-engraving as a vital craft.
WOOD ENGRAVING
Ten engraving tools are as many as will be required for ordinary purposes.
The beginner can start with five, but labour is often saved by having a
sufficient number. They should be about 3½ inches in length, according to
the size of the worker’s hand, and when held in correct position the point
of the tool should not extend beyond the end of the thumb more than half
an inch. In practice the greatest freedom is obtained when the point
extends but little beyond the thumb, but as some allowance must be made
for repeated sharpening away on the oilstone, the half-inch extension is
recommended. When purchased they are generally much longer, 6 inches, but
this length is much too great to allow the tool to be used with ease. The
makers will generally grind them down to the required length for the
purchaser, an ink mark or piece of stamp paper stuck to the tool
indicating exactly the amount to be taken off. One side of the handle is
flat, and the tool, as it enters the handle, is slightly curved upwards.
This is to allow for free passage of the hand and tool over the surface of
the wood, and though tools may be without this upward curve they lose
freedom of action by being so.
[Fig. 1]
Fig. 1
[Fig. 2]
Fig. 2
Of the ten tools, six will be known as tint-tools, three as spit-sticks,
one as scauper. The tint-tools cut lines of uniform width from extreme
fineness (No. 1) to much greater width (No. 6). They are used for tinting,
that is, cutting a series of lines to produce a tint or shade; for
outlining, especially lettering; and for scauping. The numbers used here
are for descriptive convenience only. When ordering, the actual width of
cut required should be given, otherwise the purchaser may receive
something very different from what was expected.
[Fig. 3]
Fig. 3
The spit-sticks (Nos. 1 to 3) are tools by which the cut can be easily
broadened by gradually pressing the point deeper into the wood. By keeping
to one depth they can also be used in the same manner as tint-rounded
sides and cut through the wood with smooth ease. Instead of spit-sticks,
tools known as gravers are often used. They are flat-sided, as tint-tools
are, but the spread is much greater. The cut made is the same as that made
with spit-sticks but a much greater spread is possible. The finest is
known as the lozenge graver, the broadest as the square graver. They are
used in the same manner as spit-sticks and often preferred to them, but
they lack the smooth ease of cutting which is the special feature of
spit-sticks.
[Fig. 4]
Fig. 4
The scauper, the tool of greatest width, is used for clearing away the
wood round the engraving. It is desirable that the belly part of this tool
should be sufficiently rounded: a point too square will not cut through
the wood easily. An extra tool with a square point, about the size of the
largest tint-tool, may be found useful for taking out corners.
[Fig. 5]
Fig. 5
A good selection for the beginner starting with five tools only would be
two spit-sticks (1 & 3, Fig. 3), two tint tools (4 & 6, Fig. 2), and one
scauper.
It must be clearly borne in mind that the style or character of the work
is greatly influenced by the shape of the point used. The craftsman will
be able, after a little time, to select the shape of tool which best suits
his work. Once a tool is made up, and found to be good, to alter it is not
desirable. To convert it to its old form is not easy. Rather keep an old
one to experiment with, if needful, and never chance the spoiling of a
proved tool.
For those who find a difficulty in buying tools and who wish perhaps to
have them made locally, a good plan is to buy one good tool, and have
others made to this model by the blacksmith, carpenter or other handy man.
Old files can be successfully turned into quite good engraving tools. The
point to remember is that the belly or point part of the tool be evenly
shaped on both sides. If this is not attended to, the tool will always
have a tendency to cut too much in one direction, or spring out of the
wood.
[Fig. 6]
Fig. 6
A gouge, to be used as a chisel, that is, with a mallet, is used to carve
away all wood round the engraving, so as to leave only the engraving in
relief. This is always necessary when the printing is done direct from the
wood block. It is not necessary when taking hand-proofs. A flat tool or
small chisel is useful for lowering edges which fade into white, for
preparing small plugs and for trimming straight edges.
[Fig. 7]
Fig. 7
[Fig. 8]
Fig. 8
The sandbag (Fig. 7) is made of two circular pieces of leather sewn
together and filled with fine sand. The sand is poured in just before
completing the last stitches. Any other durable substance can be used
instead of leather. On this solid yet easy base the block held by the left
hand can be turned about at will. It should be not less than five inches
across. To have it smaller may mean difficulty when engraving large
blocks. A magnifying glass is not recommended unless the eyesight is
defective. When there is defective vision it is safer and better to use a
glass and avoid strain, so it must be included as a probably necessary
thing. A double lens should be used, and should be large enough to cover a
block of 2 or 3 inches. The stand (Fig. 8) allows the lens to be turned
away, raised or lowered at will. A watchmaker’s glass can be used (for one
eye only) held in position over the eye by a piece of string round the
head. It provides only a small field of view.
[Fig. 9]
Fig. 9
Fig. 9 shows a globe filled with water, to be used at night to concentrate
the light on to the work. The light of the lamp is directly behind the
globe. A bull’s-eye lens can be used as a substitute and is equally good.
It is well to shield away by brown paper fixed to the top of the globe, or
other means, all light that does not fall on the block. It is most
unrestful to look up from work into the direct glare of a lamp; to work
without a globe or bull’s-eye with artificial light produces great
eye-strain and bad work. Good light is essential at all times.
[Fig. 10]
Fig. 10
Fig. 10 shows the roller and slab used for inking the engraving when
taking a proof. A leather roller is best but difficult to make;
composition is generally used. An old method, the method of Caxton and
quite good, is to use a dabber. The ink is dabbed on instead of rolled on.
It can be easily made, a covering of thin leather filled with rags for
padding, which must be quite firm, being all that is required (Fig. 11).
[Fig. 11]
Fig. 11
[Fig. 12]
Fig. 12
The burnisher (Fig. 12) is used for rubbing the proof off after inking the
block. Steel is best, but bone will do, or the back of a teaspoon, using
the bowl as a handle.
A supply of boxwood, proofing ink, an oilstone for sharpening tools and
some paper for taking proofs will be necessary. The paper must be thin
(India paper being the best) as it is very difficult to take a proof on
thick paper.
The table or the bench where the work is to be done must always be firm.
The craftsman should not be unduly bending over the work, but should be as
upright as possible, the height of bench and chair being adjusted to
enable the worker to see the engraving without either eye-strain or
rounding of the back and shoulders. Be comfortable when at work.
See that the tools are sharp before commencing work. If sharp the point
will always grip or “bite” when loosely “run” across the wood; if blunt it
will slide over. Always use a spare piece of boxwood when testing tools.
The face of the tool only must be sharpened (see Fig. 1). On no account
must the sharpening be done from the underneath or belly part of the tool.
Avoid bearing too much on the point; it is a quick method of sharpening,
but the angle of the face will gradually become more upright and the tool
will not cut through the wood easily. An angle of 45° is about right.
Sharpen by rubbing the face of the tool up and down the length of the
oilstone. Any lubricating oil will serve for the stone.
THE WOOD
The wood used is boxwood and where fineness of work is desired no other
wood is suitable. Dark marks sometimes indicate inferior quality; white
marks are always bad and should be avoided. Many other kinds of wood have
been tried for engraving without success, especially for work of a
moderately fine character. For large work, such as are termed posters,
sycamore and pine are principally used.
The method of producing these large blocks is called cutting. Knives, “V”
tools and gouges, instead of gravers are used, and the long grain of the
wood is the printing surface of these; whereas that which is accepted as
engraving proper is always on the end grain of the boxwood. This being the
only really reliable wood for wood engraving, and the engraver’s staple
material, it deserves more than a passing notice.
Turkey produces the finest boxwood though many good samples come from the
Crimea and the Caucasus.
The best and most valuable wood is of very slow growth, hard and heavy,
and of a very fine and close texture. The wood is sent over in logs.
Careful judgment is required in its selection when sent into the market.
It must be thoroughly seasoned before being used by the engraver as new
wood retains its moisture for a long time, is most liable to split and
warp, and is very susceptible to changes of temperature.
The measurement of the logs is from 7 to 12 inches in diameter and the
first process of blockmaking is to cut these logs into slices crosswise
about 1 inch in thickness. They are then placed singly in racks for many
months to season, and during this time sharp cracks are heard which denote
that the slices of wood are drying and splitting from the core. Owing to
this splitting, only blocks of small size can be obtained from one piece;
where larger blocks are required and also for the sake of economising
wood, it is necessary to join pieces together. The best and strongest way
is to groove and tongue them together. The sides of the pieces must be
planed true, the grooves cut and the tongues (of some hard wood) glued
into the grooves with very thin glue. They are then pressed very tightly
together with clamps and left to dry. Another way is simply to glue the
pieces together without the groove and tongue. In an even temperature they
hold together quite well, and if the block is for temporary use, little
danger need be apprehended of the joint’s opening. Always use very thin
glue thinly applied. The block has now to be planed down to about 7/8 of
an inch thickness, which is the height of type, scraped with a steel
scraper until perfectly level and smooth and finished off with the finest
sand or emery paper.
DRAWING
The highly-polished surface of the wood will not take the pencil or brush
unless prepared, and the best medium for this is flake-white and finely
ground brickdust in equal proportions. An amount sufficient to cover a
threepenny piece is enough for a block of 6 inches by 4 inches; add one or
more drops of water, and rub thinly and evenly with the fingers until it
starts to dry.
Chinese white may be used in the place of flakewhite. It can be used
without the brick-dust and applied to the wood by the fingers as before or
spread evenly by means of a soft flat brush passing by direct strokes over
the surface. This method will be quite effective, but will not give such
an even appearance as the brick-dust and white.
Indian and Chinese ink rubbed up in water and a fine camel hair brush are
used for drawing, or a pencil may be used. The best is one of medium
hardness. Too soft a pencil rubs out easily and soon gives a dirty
appearance to the drawing; one too hard is liable to bruise the wood.
All drawing on the wood must be reversed. Even in cases where this is not
necessary it is well to remember that the print from the engraving will be
a reverse of the drawing. Make reversing a habit. Much annoyance may thus
be avoided, for it is easy to produce an awkward absurdity, which, though
not apparent to other people, spoils one’s own enjoyment of the work. All
lettering must be reversed. A view of the drawing in a mirror before
commencing to engrave will reveal any incorrectness in reversing.
The engraver is to remember that the production is to be an engraving and
not a drawing; that it is to have the character of an engraving—an
engraving manifest and not an imitation of another drawing, half-tone, or
any other process. Let the dependence be on the engraving tools rather
than the pencil. As far as possible draw direct on to the wood. If this,
by the nature of the subject, is impossible, it may be necessary to trace
on to the wood.
Trace the subject firmly with a soft pencil and by waxing the sides of the
block fix the tracing tightly over it, face down. Affix one side first in
correct position, rubbing the paper on to the waxed side by means of a
tool handle or other suitable instrument, and stretch the tracing tightly
over until fixed in similar manner to the opposite side. In the absence of
beeswax, soap will do, but it is not nearly so effective, or, failing
both, the paper can be folded to the back of the block in such manner that
movement of the tracing is impossible. Being assured that there will be no
movement of the paper, trace again on to the wood by means of a hard
pencil, or preferably, a steel point. If either of these is too sharp or
pressed on too heavily, it will scratch or bruise the wood. By detaching
the paper from one side the work can be examined without fear of movement,
care being taken to fix again before continuing to trace. Only a very
faint line must be expected and this is all that is required.
Another method is to scrape some red chalk finely on to a separate piece
of paper (not too large, as it can be used over and over again) and rub it
well on until the paper is evenly reddened. Place the reddened surface
next the wood underneath the tracing—it need not be fixed—and proceed to
trace as before. This method will produce a faint red line and will be
useful when, as sometimes happens, the subject is to be reversed in the
final print.
These faint outlines must be made stronger, the drawing completed, by
means of camel hair brush and Indian ink or by pencil. Any shading can be
put into the drawing by means of these, always remembering that it is to
be finally expressed in terms of the engraving tool. To draw on the wood
is awkward without some support; a piece of wood as high as the block will
be necessary on which to rest the hand.
ENGRAVING
[Fig. 13]
Fig. 13
The tool has to be held in such a way that none of the fingers nor the
thumb is underneath it. The handle rests in the lower part of the hand,
the fourth finger in the groove of the inner part of the handle and the
third finger by its side; these two fingers touch the handle and keep it
in position within the hand. Following the third and fourth, the two
forefingers rest on the outer side of the blade while the thumb, extending
beyond the fingers almost to the point, is on the inside. The thumb is the
only part of the right hand that touches the block. The fingers touch each
other in natural order: there need be no space between any. The tool
should be laid flat upon the table, and may be taken up in one movement
(Fig. 14). Seen from below it should then show as Fig. 15. Held in this
way the tool will pass flat over the wood without any obstruction from any
part of the fingers or hand.
[Fig. 14]
Fig. 14
[Fig. 15]
Fig. 15
The block is held on the sandbag by the left hand, generally towards the
corners, which allows the greatest freedom for turning. When cutting
straight lines the block is held stationary, the tool-hand cutting
forward; when cutting curves the block is turned round, the tool-hand
remaining in one position. There is no hard rule in this, the hands acting
flexibly for each other, but it can be seen at once when engraving that a
circle cannot be cut unless the block is turned round in precise ratio to
the cuts of the tool, while to cut a straight line the wood cannot advance
to the tool’s point.
Engrave the lines one under the other, not one above the other; for
circles it is much more easy to start the cut at the top than to start
underneath, though to be able to start underneath is sometimes useful. The
flat part of the handle should be just above the surface of the wood in
cutting lines or tints, but this does not apply to all work; the angle at
which tools are held must be determined by the shapes to be taken out. Do
not attempt to cut a long line with one cut, but with a succession of
short ones, and do not cut too deeply, or the line or wood on which the
belly of the tool presses will be bruised and will print broken instead of
clean and definite. If the tool be sharp the wood will chip out crisply at
each cut; the lines should be cut out, not pushed or pressed out. Blunt
tools are more responsible for slips than anything else except perhaps a
disturbed mind.
Should there be any danger of rubbing the drawing during engraving, cover
the block with a piece of thin paper after the manner of a tracing, first
making a small hole where work is to commence.
The craftsman is advised to practise by engraving something definite,
something that can be used. Aimless cutting and digging about on bits of
wood leads nowhere, for it is a very simple matter to cut a line that need
not be cut in any particular place, whereas to cut the lines exactly to
the subject, to produce something that is required is not only getting
experience, but the result is known at once in success or failure.
[Fig. 16]
Fig. 16
[Fig. 17]
Fig. 17
Roughly speaking there are four different kinds of engraving, of which any
variations and combinations can be made. The first and most natural is to
cut white lines on black, and in many cases the subject will be
sufficiently expressed without further work; Fig. 16 is cut in this way.
Fig. 17 shows the background tinted or shaded, that is, lines cut one
under the other. Fig. 18 is the black letter cleared (scauped) away
leaving it white, while Fig. 19 shows all wood cleared away except
outlines. Bold simple lettering is an excellent subject to begin with. See
that the corners are joined cleanly: little jagged bits left in look
slovenly and print in a dirty manner.
[Fig. 18]
Fig. 18
[Fig. 19]
Fig. 19
[Fig. 20]
Fig. 20
The larger tint-tools and scaupers are used for scauping or clearing, that
is, for clearing a wide line round the work and cutting away all wood not
wanted. While doing this it is essential to protect the surrounding work
from the belly of the tool by a thin piece of card (Fig. 20). It must be
thin yet of sufficient substance to withstand the pressure of the tool,
for the work is done by levering out the wood as well as cutting it. Card
soon wears out. A thin piece of hard wood or bone will do well if smoothed
and bevelled off a little on the edge to be used under the tool. The
thickness should be about that of a penny. When scauping start the cut a
little away from the work gradually approaching until the tool has cleared
away all unnecessary wood. Smaller pieces must of course be taken away by
the smaller tools. It is a good plan to extend the first finger of the
left hand over the block until it presses against the end of the thumb of
the tool hand. This position gives great control and prevents much
slipping.
[Fig. 21]
Fig. 21
[Fig. 22]
Fig. 22
[Fig. 23]
Fig. 23
With the scauper clear a line round the work a little more than its own
width. This is sufficiently wide to enable a proof to be taken. If all the
wood is taken away it is almost impossible to proof some subjects (thin
lettering, for instance) without a hand-press, for this wood supports the
roller and burnisher and gives protection to the work while proofing.
Where a light tint shades into white as in a sky or light parts of a dress
it is necessary to lower the edges in some way before cutting, otherwise
the hard edge is apt to catch the ink and cause a smudgy objectionable
line instead of running cleanly into the white. To avoid this, lower or
scrape the hard edge into the scauping taking care not to damage the
surrounding wood. It can be done by the sharp edge of spitstick or
tint-tool, or the edge can first be lowered by a flat scauper and then
scraped smoothly into the scauping by the sharp edge of the engraving
tool. The Section Fig. 24 shows the sharp edge lowered into the scauping.
[Fig. 24]
Fig. 24
The depth of the clearing indicated in the Section is exaggerated for
purposes of clarity. If the scauping is too deep bruising of the sides is
likely; if too shallow the print will pick up the ink from the ridges at
the bottom of the scauping which have touched the ink roller.
PROOF TAKING
Place a little printer’s ink on a slab (which can be of stone, slate, or
even glass) and spread it out thinly with a knife, then roll until
distributed evenly and thinly. Avoid rolling out too much ink at once;
more can be added easily, but to take away means cleaning the whole with
turpentine and rag, or scraping with a knife. If a dabber be used, beat
the ink, which is placed more in the centre of the slab, until quite even.
The amount to roll or dab on to the block will be discovered quite easily
after a trial or two—too much ink will blur the work; too little will
print grey. Place the paper on the inked block without slurring it, and on
the paper drop a thin piece of card—a postcard will do—hold down by the
left hand and rub on the top of the card with the burnisher until an
impression is taken. The print can be examined from time to time by
lifting a corner, holding the remaining paper down firmly with the left
hand on the card. More burnishing must be applied to those parts which
have not taken the ink. If the engraved lines be fine, light pressure must
be given to the burnisher lest the lines be bruised, whereas if the parts
are black heavier pressure must be given. A little oil rubbed on one side
of the card—the side on which the burnisher is to be applied—then rubbed
off again, will allow the burnisher to slide over with ease and prevent
sticking; while if the burnisher is applied without the card, bruising is
liable to occur to fine lines. India paper is excellent on which to take
proofs by hand. Other kinds can be used if free from ridges and not too
thick. The thicker the paper the greater will be the difficulty in getting
a print, for the ink does not stick it to the block, as is the case with
thin paper, and any examination of the print nearly always moves the paper
out of position and “doubling” is the result.
This first print is often called the “overlay.” It shows not only the
engraving but all the surrounding wood and pieces between that have been
too large to be cut away by a scauper. To take a proof of the engraving
only, these black pieces on the overlay must be cut out cleanly with a
sharp knife or the point of a tint-tool, and, after inking the block
again, these pieces are placed on their corresponding parts on the wood.
They are thus blocked out—overlayed—by the pieces of paper cut from the
first print. Place fresh paper on the block and proof as before, greater
care however is necessary to prevent “doubling.” Where plenty of black is
in the engraving the process is simple, but if the subject is of thin
lines, such as fine lettering, it is a somewhat delicate operation. In
this case the less it is examined whilst the proof is being taken the
better.
During the process of engraving, in order to see exactly what has been
done so far, one may wish to take a proof. But the inking of the block
would obliterate that part of the drawing which has not yet been engraved.
Instead, therefore, of taking a proof with ink the following method will
be found convenient:—Press some _precipitated chalk_(obtainable at any
chemist’s) into the engraved part and wipe the surface clean with the palm
of the hand thus leaving the chalk in the hollows and incisions only. The
block will then appear exactly as in a print (only not reversed), i.e. the
surface of the wood will show dark against the white chalk.
PREPARING BLOCK FOR PRINTER
[Fig. 25]
Fig. 25
If the block is to be sent to the printer all unnecessary wood has to be
taken away, and if there are large surfaces this is best done by gouge and
mallet. First saw the block square to within ¼ of an inch of work, then
fix it in a vice or clamp to a bench. Use the gouge as a chisel, never
forgetting to have the cutting edge pointing towards centre of block. If
used towards the edges pieces of wood will suddenly chip away and the last
stroke of the mallet will, perhaps, ruin the work, though an experience of
this kind is seldom repeated. The block will have to be turned about in
the vice to enable the gouging to be made towards the centre and care must
be taken to hold the gouge high enough just to clear the work and so
prevent bruising. The wood must be taken away deeply. If cut too shallow,
the ridges formed by the gouge will pick up the ink from the roller which
ink again will be picked up by the paper whilst proofing. Any edges or
small pieces that the gouge cannot clear away must be trimmed off with the
scauper, the card being used to protect the work.
[Wood-cut from The Decameron, Venice, 1492. Re-engraved by R. J. Beedham.
By permission of The Shakespeare Head Press]
Wood-cut from The Decameron, Venice, 1492. Re-engraved by R. J. Beedham.
By permission of The Shakespeare Head Press
PLUGGING
If some small mistake has arisen such as a deep bruise, false cut, slip,
etc., it can be made good by plugging, that is, by the insertion of a new
piece of wood where the mistake has occurred. This requires skill and
care, for the new piece of wood must fit in exactly, otherwise a white
line will show all round it. For very small plugs the simplest method of
making a hole is to get a carpenter’s nail, round or square type,
according to the shape of the plug required, file the sides to the right
size and flatten the bottom, finally getting the edges and bottom sharp
and smooth on the oil-stone. Drive this into the wood, about 1/16 to 1/8
of an inch according to the size of the plug. Take the nail out again by a
straight pull to avoid bruising the sides, and if the nail has been
properly shaped, a clean hole with sharp edges will be the result. Into
this hole insert a piece of boxwood, trimmed to exact size by means of a
flat tool or chisel, then gently hammer with a piece of wood until the
bottom of the hole is felt. To dip the end of the plug into thin glue or
gum before insertion will help to keep it fast, but small plugs accurately
trimmed will hold without glue. For larger plugs glue must be used.
[Fig. 26]
Fig. 26
Through a thin piece of card cut a hole large enough to allow the head of
the plug to protrude, place it in the block to protect the engraving, then
cut off the projecting head close to the card with a fine saw. By means of
the scauper and card, always cutting towards the centre, lower the
remaining projection until nearly level with surrounding surface, and
finish off with the chisel laid flat on the block. An excellent tool with
which to get the plug level is a fine tint-tool laid on its side and used
as a chisel, chisel or tint-tool being used in a slicing movement and not
driven.
Two or three plugging nails, made ready and kept for the purpose, will be
all that are required for smaller plugs. The holes can also be made by
drills such as are used for fretwork. Larger plugs must be scauped or
chiselled out, taking care that the sides go straight down and that the
edges are without a bruise. The larger the plug, the deeper must be the
hole, the depth for large plugs being half-way through the block. Plugs on
the extreme edge of the block require more care but the difficulties can
nearly always be overcome by a little ingenuity. A drop of water placed on
a bruise will often bring it to the surface again. Hot water is still more
effective, while, if the bruising is deep and general, steaming the whole
surface is the best method though it makes the wood rotten and
disagreeable to cut on afterwards.
APPENDIX
The beginner should commence with patterns and pictures of white lines on
black. The normal development of this first method is the silhouette with
white lines upon it. Having attained skill with gravers and scaupers he
may proceed to engrave patterns and pictures of black lines on white,
first in plain outline, and then, last of all, he may attempt the
modelling and elaboration of the general surface.
NOTE ON WOOD-CUTS
The method of wood-engraving which is described in this book is distinct
from that known properly as “wood-cutting”. The “woodcut” is done with a
knife on the long grain of the wood instead of the end grain. It is
necessarily done on soft wood and is therefore less suitable for use in
conjunction with type in a printing press, except for large work. But the
wood-engraver should certainly practise the art of wood-cutting also and
for the purpose he will require, in addition to some planks of pear wood
or a similar fine-grained wood, a knife and several wood-carver’s chisels
and gouges—the first for cutting lines and edges and the latter for
cutting away the background. The knife (Fig. 27) is the most important of
these tools and the best form is like a very fine carpenter’s chisel with
a small handle, such as can be grasped in the fingers, a short blade about
one inch long, three-eighths of an inch wide and as thin as that of a
pen-knife, with the cutting end ground at an angle of about 30° with the
upper edge.
It is held very much as a pen is held for writing and, of course, the cut
is made always in the direction which does not burr the grain of the wood
just as a skewer is sharpened by cutting towards and not away from its
point.
Although in connection with the printing press the wood-cut has not the
same usefulness as the wood-engraving on account of the soft wood
necessarily used and the impossibility of doing the finest work with the
same degree of precision, nevertheless, as an independent art that of
wood-cutting is on an equality with any other, and, in one respect, the
fact that only soft wood can be used is an advantage; for such wood, pine
or pear, is more easy to get than a hard foreign wood like the Turkish
box-wood. The wood-cutter may therefore go into his own back garden for
his material and is independent of the foreign merchant. The difficulty of
the wood-engraver in this matter is, however, not quite insuperable, for,
if properly seasoned and prepared, holly or blackthorn are quite good for
end grain work and, though not as hard as boxwood, make a very fair
substitute.
[Alphabet, by Reynolds Stone. (By permission of Burns, Gates & Washbourne,
Ltd.)]
Alphabet, by Reynolds Stone _(By permission of Burns, Gates & Washbourne,
Ltd.)_
[From Forrest Reid’s Apostate, by Reynolds Stone (By permission of Faber &
Faber, Ltd.) ]
_From_ Forrest Reid’s Apostate, by Reynolds Stone _(By permission of Faber
& Faber, Ltd.)_
[Winter, from a sketch by Verrall, by R. J. Beedham ]
Winter, from a sketch by Verrall, by R. J. Beedham
[Strawberry Picking, by Claire Leighton (By permission of Victor Gollancz)
]
Strawberry Picking, by Claire Leighton _(By permission of Victor
Gollancz)_
[March, by Mrs. G. Raverat ]
March, by Mrs. G. Raverat
[“Miss Jenkyns reading Rasselas,” by Joan Hassal. (By permission of George
G. Harrap & Co., Ltd.) ]
“Miss Jenkyns reading Rasselas,” by Joan Hassall _(By permission of George
G. Harrap & Co., Ltd.)_
[The Cottage, by Robert Gibbings ]
The Cottage, by Robert Gibbings
[John Dickinson and Company advertisement ]
[Spicers Ltd. advertisement ]
***END OF THE PROJECT GUTENBERG EBOOK WOOD ENGRAVING***
CREDITS
January 6, 2014
Project Gutenberg edition 10
Martin Schub
A WORD FROM PROJECT GUTENBERG
This file should be named 44606‐0.txt or 44606‐0.zip.
This and all associated files of various formats will be found in:
http://www.gutenberg.org/dirs/4/4/6/0/44606/
Updated editions will replace the previous one — the old editions will be
renamed.
Creating the works from public domain print editions means that no one
owns a United States copyright in these works, so the Foundation (and
you!) can copy and distribute it in the United States without permission
and without paying copyright royalties. Special rules, set forth in the
General Terms of Use part of this license, apply to copying and
distributing Project Gutenberg™ electronic works to protect the Project
Gutenberg™ concept and trademark. Project Gutenberg is a registered
trademark, and may not be used if you charge for the eBooks, unless you
receive specific permission. If you do not charge anything for copies of
this eBook, complying with the rules is very easy. You may use this eBook
for nearly any purpose such as creation of derivative works, reports,
performances and research. They may be modified and printed and given away
— you may do practically _anything_ with public domain eBooks.
Redistribution is subject to the trademark license, especially commercial
redistribution.
THE FULL PROJECT GUTENBERG LICENSE
_Please read this before you distribute or use this work._
To protect the Project Gutenberg™ mission of promoting the free
distribution of electronic works, by using or distributing this work (or
any other work associated in any way with the phrase “Project Gutenberg”),
you agree to comply with all the terms of the Full Project Gutenberg™
License (available with this file or online at
http://www.gutenberg.org/license).
Section 1.
General Terms of Use & Redistributing Project Gutenberg™ electronic works
1.A.
By reading or using any part of this Project Gutenberg™ electronic work,
you indicate that you have read, understand, agree to and accept all the
terms of this license and intellectual property (trademark/copyright)
agreement. If you do not agree to abide by all the terms of this
agreement, you must cease using and return or destroy all copies of
Project Gutenberg™ electronic works in your possession. If you paid a fee
for obtaining a copy of or access to a Project Gutenberg™ electronic work
and you do not agree to be bound by the terms of this agreement, you may
obtain a refund from the person or entity to whom you paid the fee as set
forth in paragraph 1.E.8.
1.B.
“Project Gutenberg” is a registered trademark. It may only be used on or
associated in any way with an electronic work by people who agree to be
bound by the terms of this agreement. There are a few things that you can
do with most Project Gutenberg™ electronic works even without complying
with the full terms of this agreement. See paragraph 1.C below. There are
a lot of things you can do with Project Gutenberg™ electronic works if you
follow the terms of this agreement and help preserve free future access to
Project Gutenberg™ electronic works. See paragraph 1.E below.
1.C.
The Project Gutenberg Literary Archive Foundation (“the Foundation” or
PGLAF), owns a compilation copyright in the collection of Project
Gutenberg™ electronic works. Nearly all the individual works in the
collection are in the public domain in the United States. If an individual
work is in the public domain in the United States and you are located in
the United States, we do not claim a right to prevent you from copying,
distributing, performing, displaying or creating derivative works based on
the work as long as all references to Project Gutenberg are removed. Of
course, we hope that you will support the Project Gutenberg™ mission of
promoting free access to electronic works by freely sharing Project
Gutenberg™ works in compliance with the terms of this agreement for
keeping the Project Gutenberg™ name associated with the work. You can
easily comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg™ License when you
share it without charge with others.
1.D.
The copyright laws of the place where you are located also govern what you
can do with this work. Copyright laws in most countries are in a constant
state of change. If you are outside the United States, check the laws of
your country in addition to the terms of this agreement before
downloading, copying, displaying, performing, distributing or creating
derivative works based on this work or any other Project Gutenberg™ work.
The Foundation makes no representations concerning the copyright status of
any work in any country outside the United States.
1.E.
Unless you have removed all references to Project Gutenberg:
1.E.1.
The following sentence, with active links to, or other immediate access
to, the full Project Gutenberg™ License must appear prominently whenever
any copy of a Project Gutenberg™ work (any work on which the phrase
“Project Gutenberg” appears, or with which the phrase “Project Gutenberg”
is associated) is accessed, displayed, performed, viewed, copied or
distributed:
This eBook is for the use of anyone anywhere at no cost and with
almost no restrictions whatsoever. You may copy it, give it away
or re-use it under the terms of the Project Gutenberg License
included with this eBook or online at http://www.gutenberg.org
1.E.2.
If an individual Project Gutenberg™ electronic work is derived from the
public domain (does not contain a notice indicating that it is posted with
permission of the copyright holder), the work can be copied and
distributed to anyone in the United States without paying any fees or
charges. If you are redistributing or providing access to a work with the
phrase “Project Gutenberg” associated with or appearing on the work, you
must comply either with the requirements of paragraphs 1.E.1 through 1.E.7
or obtain permission for the use of the work and the Project Gutenberg™
trademark as set forth in paragraphs 1.E.8 or 1.E.9.
1.E.3.
If an individual Project Gutenberg™ electronic work is posted with the
permission of the copyright holder, your use and distribution must comply
with both paragraphs 1.E.1 through 1.E.7 and any additional terms imposed
by the copyright holder. Additional terms will be linked to the Project
Gutenberg™ License for all works posted with the permission of the
copyright holder found at the beginning of this work.
1.E.4.
Do not unlink or detach or remove the full Project Gutenberg™ License
terms from this work, or any files containing a part of this work or any
other work associated with Project Gutenberg™.
1.E.5.
Do not copy, display, perform, distribute or redistribute this electronic
work, or any part of this electronic work, without prominently displaying
the sentence set forth in paragraph 1.E.1 with active links or immediate
access to the full terms of the Project Gutenberg™ License.
1.E.6.
You may convert to and distribute this work in any binary, compressed,
marked up, nonproprietary or proprietary form, including any word
processing or hypertext form. However, if you provide access to or
distribute copies of a Project Gutenberg™ work in a format other than
“Plain Vanilla ASCII” or other format used in the official version posted
on the official Project Gutenberg™ web site (http://www.gutenberg.org),
you must, at no additional cost, fee or expense to the user, provide a
copy, a means of exporting a copy, or a means of obtaining a copy upon
request, of the work in its original “Plain Vanilla ASCII” or other form.
Any alternate format must include the full Project Gutenberg™ License as
specified in paragraph 1.E.1.
1.E.7.
Do not charge a fee for access to, viewing, displaying, performing,
copying or distributing any Project Gutenberg™ works unless you comply
with paragraph 1.E.8 or 1.E.9.
1.E.8.
You may charge a reasonable fee for copies of or providing access to or
distributing Project Gutenberg™ electronic works provided that
- You pay a royalty fee of 20% of the gross profits you derive from
the use of Project Gutenberg™ works calculated using the method you
already use to calculate your applicable taxes. The fee is owed to
the owner of the Project Gutenberg™ trademark, but he has agreed to
donate royalties under this paragraph to the Project Gutenberg
Literary Archive Foundation. Royalty payments must be paid within 60
days following each date on which you prepare (or are legally
required to prepare) your periodic tax returns. Royalty payments
should be clearly marked as such and sent to the Project Gutenberg
Literary Archive Foundation at the address specified in Section 4,
“Information about donations to the Project Gutenberg Literary
Archive Foundation.”
- You provide a full refund of any money paid by a user who notifies
you in writing (or by e-mail) within 30 days of receipt that s/he
does not agree to the terms of the full Project Gutenberg™ License.
You must require such a user to return or destroy all copies of the
works possessed in a physical medium and discontinue all use of and
all access to other copies of Project Gutenberg™ works.
- You provide, in accordance with paragraph 1.F.3, a full refund of
any money paid for a work or a replacement copy, if a defect in the
electronic work is discovered and reported to you within 90 days of
receipt of the work.
- You comply with all other terms of this agreement for free
distribution of Project Gutenberg™ works.
1.E.9.
If you wish to charge a fee or distribute a Project Gutenberg™ electronic
work or group of works on different terms than are set forth in this
agreement, you must obtain permission in writing from both the Project
Gutenberg Literary Archive Foundation and Michael Hart, the owner of the
Project Gutenberg™ trademark. Contact the Foundation as set forth in
Section 3 below.
1.F.
1.F.1.
Project Gutenberg volunteers and employees expend considerable effort to
identify, do copyright research on, transcribe and proofread public domain
works in creating the Project Gutenberg™ collection. Despite these
efforts, Project Gutenberg™ electronic works, and the medium on which they
may be stored, may contain “Defects,” such as, but not limited to,
incomplete, inaccurate or corrupt data, transcription errors, a copyright
or other intellectual property infringement, a defective or damaged disk
or other medium, a computer virus, or computer codes that damage or cannot
be read by your equipment.
1.F.2.
LIMITED WARRANTY, DISCLAIMER OF DAMAGES — Except for the “Right of
Replacement or Refund” described in paragraph 1.F.3, the Project Gutenberg
Literary Archive Foundation, the owner of the Project Gutenberg™
trademark, and any other party distributing a Project Gutenberg™
electronic work under this agreement, disclaim all liability to you for
damages, costs and expenses, including legal fees. YOU AGREE THAT YOU HAVE
NO REMEDIES FOR NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY OR BREACH
OF CONTRACT EXCEPT THOSE PROVIDED IN PARAGRAPH F3. YOU AGREE THAT THE
FOUNDATION, THE TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT
WILL NOT BE LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL,
PUNITIVE OR INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY
OF SUCH DAMAGE.
1.F.3.
LIMITED RIGHT OF REPLACEMENT OR REFUND — If you discover a defect in this
electronic work within 90 days of receiving it, you can receive a refund
of the money (if any) you paid for it by sending a written explanation to
the person you received the work from. If you received the work on a
physical medium, you must return the medium with your written explanation.
The person or entity that provided you with the defective work may elect
to provide a replacement copy in lieu of a refund. If you received the
work electronically, the person or entity providing it to you may choose
to give you a second opportunity to receive the work electronically in
lieu of a refund. If the second copy is also defective, you may demand a
refund in writing without further opportunities to fix the problem.
1.F.4.
Except for the limited right of replacement or refund set forth in
paragraph 1.F.3, this work is provided to you ’AS-IS,’ WITH NO OTHER
WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
WARRANTIES OF MERCHANTIBILITY OR FITNESS FOR ANY PURPOSE.
1.F.5.
Some states do not allow disclaimers of certain implied warranties or the
exclusion or limitation of certain types of damages. If any disclaimer or
limitation set forth in this agreement violates the law of the state
applicable to this agreement, the agreement shall be interpreted to make
the maximum disclaimer or limitation permitted by the applicable state
law. The invalidity or unenforceability of any provision of this agreement
shall not void the remaining provisions.
1.F.6.
INDEMNITY — You agree to indemnify and hold the Foundation, the trademark
owner, any agent or employee of the Foundation, anyone providing copies of
Project Gutenberg™ electronic works in accordance with this agreement, and
any volunteers associated with the production, promotion and distribution
of Project Gutenberg™ electronic works, harmless from all liability, costs
and expenses, including legal fees, that arise directly or indirectly from
any of the following which you do or cause to occur: (a) distribution of
this or any Project Gutenberg™ work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg™ work, and (c) any Defect
you cause.
Section 2.
Information about the Mission of Project Gutenberg™
Project Gutenberg™ is synonymous with the free distribution of electronic
works in formats readable by the widest variety of computers including
obsolete, old, middle-aged and new computers. It exists because of the
efforts of hundreds of volunteers and donations from people in all walks
of life.
Volunteers and financial support to provide volunteers with the assistance
they need, is critical to reaching Project Gutenberg™’s goals and ensuring
that the Project Gutenberg™ collection will remain freely available for
generations to come. In 2001, the Project Gutenberg Literary Archive
Foundation was created to provide a secure and permanent future for
Project Gutenberg™ and future generations. To learn more about the Project
Gutenberg Literary Archive Foundation and how your efforts and donations
can help, see Sections 3 and 4 and the Foundation web page at
http://www.pglaf.org.
Section 3.
Information about the Project Gutenberg Literary Archive Foundation
The Project Gutenberg Literary Archive Foundation is a non profit
501(c)(3) educational corporation organized under the laws of the state of
Mississippi and granted tax exempt status by the Internal Revenue Service.
The Foundation’s EIN or federal tax identification number is 64-6221541.
Its 501(c)(3) letter is posted at
http://www.gutenberg.org/fundraising/pglaf. Contributions to the Project
Gutenberg Literary Archive Foundation are tax deductible to the full
extent permitted by U.S. federal laws and your state’s laws.
The Foundation’s principal office is located at 4557 Melan Dr.
S. Fairbanks, AK, 99712., but its volunteers and employees are scattered
throughout numerous locations. Its business office is located at 809 North
1500 West, Salt Lake City, UT 84116, (801) 596-1887, email
business@pglaf.org. Email contact links and up to date contact information
can be found at the Foundation’s web site and official page at
http://www.pglaf.org
For additional contact information:
Dr. Gregory B. Newby
Chief Executive and Director
gbnewby@pglaf.org
Section 4.
Information about Donations to the Project Gutenberg Literary Archive
Foundation
Project Gutenberg™ depends upon and cannot survive without wide spread
public support and donations to carry out its mission of increasing the
number of public domain and licensed works that can be freely distributed
in machine readable form accessible by the widest array of equipment
including outdated equipment. Many small donations ($1 to $5,000) are
particularly important to maintaining tax exempt status with the IRS.
The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United States.
Compliance requirements are not uniform and it takes a considerable
effort, much paperwork and many fees to meet and keep up with these
requirements. We do not solicit donations in locations where we have not
received written confirmation of compliance. To SEND DONATIONS or
determine the status of compliance for any particular state visit
http://www.gutenberg.org/fundraising/donate
While we cannot and do not solicit contributions from states where we have
not met the solicitation requirements, we know of no prohibition against
accepting unsolicited donations from donors in such states who approach us
with offers to donate.
International donations are gratefully accepted, but we cannot make any
statements concerning tax treatment of donations received from outside the
United States. U.S. laws alone swamp our small staff.
Please check the Project Gutenberg Web pages for current donation methods
and addresses. Donations are accepted in a number of other ways including
checks, online payments and credit card donations. To donate, please
visit: http://www.gutenberg.org/fundraising/donate
Section 5.
General Information About Project Gutenberg™ electronic works.
Professor Michael S. Hart is the originator of the Project Gutenberg™
concept of a library of electronic works that could be freely shared with
anyone. For thirty years, he produced and distributed Project Gutenberg™
eBooks with only a loose network of volunteer support.
Project Gutenberg™ eBooks are often created from several printed editions,
all of which are confirmed as Public Domain in the U.S. unless a copyright
notice is included. Thus, we do not necessarily keep eBooks in compliance
with any particular paper edition.
Each eBook is in a subdirectory of the same number as the eBook’s eBook
number, often in several formats including plain vanilla ASCII, compressed
(zipped), HTML and others.
Corrected _editions_ of our eBooks replace the old file and take over the
old filename and etext number. The replaced older file is renamed.
_Versions_ based on separate sources are treated as new eBooks receiving
new filenames and etext numbers.
Most people start at our Web site which has the main PG search facility:
http://www.gutenberg.org
This Web site includes information about Project Gutenberg™, including how
to make donations to the Project Gutenberg Literary Archive Foundation,
how to help produce our new eBooks, and how to subscribe to our email
newsletter to hear about new eBooks.
***FINIS***